Aluminum 3.5 inch Impeller
These impellers are included with the RetroFit Kit for the Cyclone Sample Mill and they are available as replacements.
Note: Use with the RetroFit kit only.

Part Number   30-0477
Price: $173.80   Quantity    

Nickel Grinding Ring can be substituted for the standard copper grinding ring. These are formed and fitted by us. The Ni Grinding Ring provides long life and is recommended for special samples where copper grinding rings are not permitted.

Part Number   30-0480
Price: $444.40   Quantity    

Low mass materials such as forages, leaves, and wood chips can be introduced in larger initial sizes by using the optional Forage Cover.
The Forage Cover permits feeding forage core samples directly into the Mill without preliminary grinding.
Cover includes: gasket and o-rings.
(gasket color may vary)

Part Number   30-0367
Price: $332.20   Quantity    

Replacement Gaskets for the Forage and / or Grain Cover used on the Cyclone Sample Mill.

Adhesive back Acrylic .06 thick (color may vary)

Part Number   30-0486
Price: $26.40   Quantity  

5 Pack
Part Number   30-0486P5
Price: $127.60   Quantity  

10 Pack
Part Number   30-0486P10
Price: $243.10   Quantity    

Retrofit kit is especially designed to grind products with higher moisture or higher fat content than our standard Mill setup. Includes products such as oilseeds, soybeans, meals, etc. Also, this device will allow more through-put on drier products than the standard Mill because of increased screen surface area.

The Retrofit is easy to install. Simply remove the standard Screen and Impeller and replace them with the Retrofit Pan, Impeller and Screen (360°).

The Retrofit kit includes a Retrofit Pan with gasket attached, Retrofit Impeller, Clean-Out Tool, 1.0 mm Screen (other sizes available) and Hex Key. A Forage Cover and vacuum recommended for use with larger samples.

Part Number   30-0598
Price: $1039.50   Quantity    

Special modified fittings for the Mill Enclosure Vacuum attachment.

Vacuum for 35-0497 Mill enclosure with vacuum box. Powerful 2 horse motor to help with Mill operation cleanup.

Part Number   30-0175
Price: $133.10   Quantity    

Sample Feed Controller: Net weight: 1.5 kg (3.3 lb). Shipping weight: 1.6 kg (4.5 lb). Auger forward and reverse operation at 52 rpm 120V with 60 Hz, or 50 rpm with 50 Hz. Hopper capacity: 250 ml.

Part Number:   3010-016   115 Volt
Price: $1039.50   Quantity  

Part Number:   3010-015   220 Volt
Price: $1039.50   Quantity    

HMHF/RETROFIT
Product media screen filter for
Cyclone Sample Mill
Note: Use with the RetroFit kit only.

HMHF/RETROFIT S.S. SCREEN 1.0 MM
Part Number:   30-0472  
Price: $190.30   Quantity  

CYCLONE SAMPLE MILL ( NICKEL PLATED ALUMINUM)
Part Number:   3010-075  
Price: $6865.10   Quantity  

CYCLONE SAMPLE MILL DIRECT DRIVE (Aluminum Chamber )
Part Number:   3010-090  
Price: $4395.60   Quantity  

Filter media for the Air outlet filter assembly.

Part Number:   30-0308
Price: $6.60   Quantity    

2 Matched Belts per Set
Replacement belts for the Cyclone Sample Mill
Model Number: 3010-080P
Model Number: 3010-081P
(Not for Joined Belt Drive)

Part Number:   35-0353
Price: $67.10   Quantity    

Drive belts for the Cyclone Sample Mill.
These are matched belt pairs for replacement. They must be changed at the same time.
Replacement belts for the Cyclone Sample Mill
Model Number: 3010-030 and 3010-019
Model Number: 3010-060 and 3010-061

Part Number:   35-0433
Price: $127.60   Quantity    

Copper Grinding Ring
99.9% copper — nothing added
NON MAGNETIC
Diamond Grinding Pattern
( Like our Stainless Steel Grinding Ring.)

Grinding ring for all UDY CYCLONE SAMPLE mills
Save when ordering 30-0334P5

Part Number:   30-0334
Price: $298.00   Quantity    

Copper Grinding Ring
STANDARD Grinding ring for all UDY CYCLONE SAMPLE mills

Part Number:   30-0335
Price: $243.10   Quantity  

5 Pack
Part Number:   30-0335P5
Price: $1007.60   Quantity    

Replacement part. Cover in place - micro safety switch
Prevents mill from starting if cover is not in place.
Includes:
Lever Standoff
Prepped attaching wires
Mounting Bracket and Hardware

  Part Number:   30-0398
Price: $81.40   Quantity    

Standard Aluminum Grinding Impeller 8MM
For most grains.

Part Number:   30-0316
Price: $136.40   Quantity  

5 Pack
Part Number:   30-0316P5
Price: $605.00   Quantity  

10 Pack
Part Number:   30-0316P10
Price: $1126.40   Quantity    

AIR SEPARATOR
Replacement part. Fits on top of the Grinding Chamber.
See Grinding Chamber Above. (Molded Part)

Part Number:   30-0339
Price: $28.60   Quantity  

Original Grain Cover
for the Cyclone Sample Mill.

Includes:
Ben Gate
Thumb Screw
Gasket and O-rings
Ready for resale as a replacement part or with a new mill.

Part Number:   30-0368
Price: $248.60   Quantity    

GRINDING CHAMBER WITH SAFETY COVER
Includes: Clamp mounting holes,
Pem studs for spring tension assembly
safety cover
retainer ring - (drive bearing assembly)
ready for assembly
(Does not include Drive Bearing Assembly)

Part Number:   30-0455
Price: $675.40   Quantity  

High-Speed impeller side of mill drive..
1. Upper drive bearing 35-0460
2. Lower drive bearing 35-0461
3. Center washer 30-0348
4. Drive Bearing shaft 30-0344
5. Retaining Ring 35-0345
Does not Include pulley
These bearings fit both Joined belt and Polyflex

Part Number:   30-0385
Price: $225.50   Quantity    

Cyclone Body Cleaning Brush

Part Number:   35-0470
Price: $7.70   Quantity    

For Cyclone Sample Mill
Cyclone body with bottle seal
( Replacement part for the Mill Chamber)

Part Number:   35-0340
Price: $83.60   Quantity    

Main on / off switch for the
Cyclone Sample Mill.
Includes switch, boot and function tag.
DPST

Part Number:   35-0324
Price: $71.50   Quantity    

Air outlet filter assembly
Funnels and lids with filter media.
Complete.

Part Number:   30-0307
Price: $30.80   Quantity    

KIT INCLUDES:
2 Glass 120 ML bottle
1 Plastic 150 ML bottle

Part Number:   30-0387
Price: $37.40   Quantity    

Replacement part for in-service Joined Belt Cyclone Sample Mills.
Part of the Spring Tension Assembly.
This is the complete Idler pulley assembly.
This Item includes 2 bearings, a spacer, 2 clips, and a pulley.

Part Number:   35-0434
Price: $687.50   Quantity    

Clamps are mounted on the mill chamber to hold chamber covers in place. Sold as set of four.

Part Number:   35-0331
Price: $46.20   Quantity    

Idler Pulley ONLY
for the Cyclone Sample Mill.
Machined stainless steel for long life.
Available as a replacement part. Requires bearings, spacer, and retaining clips.

See 35-0434 for complete assembly.

Part Number:   30-0432
Price: $572.00   Quantity    

No Belts, 115V 60HZ 1/2 Hp Motor same
as the 3010-014 except with an aluminum chamber. This Mill is a standard in labs requiring a workhorse. Now with the aluminum chamber for longer life.

Note: This Mill is also available with a Nickel plated chamber. part number: 3010-095

Part Number:   3010-090
Price: $4395.60   Quantity    

Part Number:   3010-095     Nickel Plated Aluminum Chamber
Price: $5055.60   Quantity    

Joined Belt Drive
( NICKEL Plated Aluminum CHAMBER )
This is the Nickel Chamber Mill just like Our Standard 3010-030/019/060/061 except it comes with a nickel plated aluminum grinding chamber (you can also add a nickel plated impeller and stainless steel Grinding ring.

  

- More Mill Info

Part Number:   3010-075
Price: $6865.10   Quantity